Alpha Rain 540-222-1642 Solar roofing fans for metal roofing in leesburg va, I will show and describe our custom made solar roofing fans. We are alpha rain the metal roofing company. Take a look at our video and please check us out at https://alpharain.com/contact-us/ 540-222-1642

Here are other videos made just for Leesburg Va

https://www.youtube.com/user/AlphaRainRoofing 
1. Vented J Channel: https://www.youtube.com/watch?v=VJQTyqBTyfo
2. Snowbirds: https://www.youtube.com/watch?v=uXpAdmCbxac
3. W Valley: https://www.youtube.com/watch?v=o7Rz0ei24xE
4. Radiant Barrier: https://www.youtube.com/watch?v=x844FTJLGHc
5. Chimney Flashing: https://www.youtube.com/watch?v=nuGUqPOIdBY
6. Double Lock Panel: https://www.youtube.com/watch?v=m7TZZBYcA00
7. Metal Roofing Pre-Painted: https://www.youtube.com/watch?v=htdFLu64XNQ
8. Vented Ridge Cap: https://www.youtube.com/watch?v=678236SR8Nw
9. Custom Drip Edge: https://www.youtube.com/watch?v=WnZ0iv7yeqo
10. Metal Roofing Screws or Nails: https://www.youtube.com/watch?v=rlqkwsGi5MA
11. Metal Roofing Matte Paint Glossy Paint: https://www.youtube.com/watch?v=rk-xYEUWvkE
12. Galvalume or Galvanized: https://www.youtube.com/watch?v=fd41UpBbTAA
13. Attic Venting: https://www.youtube.com/watch?v=NskY1bsFuKQ

Connect with Alpha Rain
https://www.facebook.com/pages/Alpha-Rain-Metal-Roofing/463335185396
https://plus.google.com/+Alpharainmetalroofs
https://twitter.com/MetalRoofingVA
https://www.youtube.com/user/AlphaRainRoofing

Ask A Question:
https://alpharain.com/contact-us/#
Our Blog:
https://alpharain.com/blog/
Our Local Blogs
http://leesburgmetalroofing.wordpress.com/
http://warrentonmetalroofing.wordpress.com/
http://culpepermetalroofing.wordpress.com/
http://charlottesvillemetalroofing.wordpress.com/
http://fredericksburgmetalroofing.wordpress.com/
http://arlingtonvametalroofing.wordpress.com/
http://fairfaxmetalroofing.wordpress.com/
http://middleburgmetalroofing.wordpress.com/

Please fill out your information below if you are interest in a Metal Roofing or this video post.

Solar roofing vans for Leesburg VA Metal Roofing, I will show and describe our custom made solar roofing fans. We are alpha rain the metal roofing company. Take a look at our video and please check us out at https://alpharain.com/contact-us/ or you can reach us at 540-222-1642

The short answer is no…BUT! If you add a thermal break and a Radiant barrier you can easily achieve a 50 plus drop in attic temperature. We have consistently dropped attic temps from the 160-degree mark to about 103 degrees and it doesn’t matter if the roof is asphalt shingle, wood shake or metal roof.

This home had over 160-degree attic temperature which made the upstairs master bedroom unbearable. We installed our “system” and during the hottest week on record, the master bedroom was the coolest it had ever been. This “system” really works!

Stay tuned for how we do it or look at our Energy Efficient Roof Ventilation System FAQ page.

Have you ever wondered how the vertical standing seam panels are lined up correctly on a gable roof? As you know a gable roof is a simple up and over roofline much like a small two-man pup tent is. In this case, you simply measure to the middle to determine how wide a panel to start with. Then you start at one end and install the panels one at a time working from one end to the other.

On a hip roof, it is much more difficult. If you look at a hip roof you will notice a that as the hip goes from the peak to the eave that each panel gets shorter until it ends. Therefore if you started at one end the panel would be so small that it would be impossible to know if it was correctly lined up until about the halfway point. Most metal roof installers make the panels and loosely lay them on the deck until they get to the halfway point. Then they get them lined up and start seaming them. This is still not very precise. As far as I know, we are the only installers that hand make a double male leg panel. We install this panel in the very center and then we install all the panels to the left and then start at the middle and install all of the panels to the right to make a perfectly aligned roof. As you can see from this photo the center panel is the panel we installed first. Then we installed from the center out all the panels on the left and right. The difficult part is hand make the center panel. Our installers excel at hand made flashing and you can’t tell the difference between their hand bent panel and the machine extruded panels.